Complete choke cable, one barrel nipple at handlebar choke lever

We advise you to measure your existing cable before ordering in case you have a non standard set up.

 1 in stock

 30132825 GU30132825 30 13 28 25
 3013 2825 3013.2825 30.13.28.25

Upper throttle cable, runs from twistgrip to splitter under tank

One upper cable needed, this cable is for Domino switchgear. We advise you to measure your existing cable before ordering in case you have a non standard set up.

 1 in stock

 28117534 GU28117534 28 11 75 34
 2811 7534 2811.7534 28.11.75.34

Closing throttle cable

We advise you to measure your existing cable before ordering in case you have a non standard set up

 1 in stock

 883002 MG883002

Oil temperature sensor

See ELA03330 for sensor support

 1 in stock

 29724961 GU29724961 29 72 49 61
 2972 4961 2972.4961 29.72.49.61

Rubber gasket for sealing fuel pump to fuel tank

Only for models with the part number 05107230 on the fuel pump flange

 1 in stock

 05107430 GU05107430 05 10 74 30
 0510 7430 0510.7430 05.10.74.30

Also fits Aprilia Pegaso (2005-2009)

Dellorto V5 slide needle for VHB 30 carbs. The original V9 needle has limited availability and this is the closest alternative. Drop the V5 needle by one groove to simulate the V9 needle

The V5 needle has also been discontinued so stocks are limited. Standard needle clip position is 2nd groove from top

 1 in stock

 13937700 GU13937700 13 93 77 00
 1393 7700 1393.7700 13.93.77.00

Carb mounted flip choke with plunger, lever, O ring, casting and spring. Insufficient clearance on high top carbs to operate the choke and the throttle cable

Fits all PHF30 - PHF36 and VHB30 Dellorto flat top carbs, contains rubber seat insert. Allows you to eliminate the choke cables and any handlebar choke controls for a cleaner look, especially suitable for special builds

 1 in stock

 14937800 GU14937800 14 93 78 00
 1493 7800 1493.7800 14.93.78.00

Carb gasket kit / rebuild kit for Dellorto PHBH carbs

Carb overhaul kit, float bowl seal FUA90001, fuel filter FUA60888 and float bowl washer FUA27720 available separately to this carb seal kit

 1 in stock

 19939980 GU19939980 19 93 99 80
 1993 9980 1993.9980 19.93.99.80

Airbox breather pipes, attach to underside of airbox

Also known as Guzzi ref. 19159600 for small twins

 1 in stock

28157050-z 28157050 GU28157050 28 15 70 50
 2815 7050 2815.7050 28.15.70.50

Plastic inlet manifold, replaces unavailable aluminium manifold. Suitable for PHF 30 carb conversions on models previously fitted with VHB30 carbs. Contains inlet manifold, gasket, O rings, clip and M6 bolts to secure to head. Carb mounts direct to this manifold (no inlet manifold rubber required)

Note that on models with M8 inlet manifold bolts and standard heads (T3, 1000 SP) it will be necessary to drill out the manifold bolt holes from 6mm to 8mm to reuse your existing bolts. Can be used to replace PHF30 inlet manifolds 17116265 and 17116365 which are no longer available. These manifolds exit the heads at a different angle to VHB manifolds and in some cases you may need to modify side panels to allow clearance for air filters

 1 in stock